Arduino gps gsm with SIM548C Board

Arduino gps gsm with SIM548C Board

Want your Arduino GPS positioning, text messaging, the phone function, you only need this three-in-one module can be achieved.

GPS / GPRS / GSM communication module is based on a combination of SIMCOM Company SIM548C design, the GSM / GPRS & GPS functionality as a whole.

Positioning through GPS functionality, GSM SMS, GSM phone, GPRS TCP / IP protocol GPS data or other data sent to the remote. Compatible with Arduino Interface Specification.

Play to your imagination and innovation capability, use your cell phone via SMS remote control all the things you want to control.

Specifications:

• Operating power: 5 ~ 12V
• Operating Current: usually current? MA, the actual transient current up to 2A
• Operating Temperature: -30 ° C ~ +80 ° C
• Module dimensions: length 82mm, width 70mm
• Quad-band GSM / GPRS 850/900/1800/1900MHz
• GPRS multi-the slot the Class 10 standard
• GPRS mobile station a Class B standards
• meet the GSM 2/2 + standards
-Class 4 (2W @ GSM850/900MHz)
-Class 1 (1W @ GSM1800/1900MHz)
• AT command and control (GSM 07.07, 07.05 and the SIMCom enhanced AT command set)
GPS indicator
• Receiver 20 channels, L1 1575.42 MHz, C / A code 1,023 MHz chip rate
• accurate positioning of the 2.5 m CEP
- Without the SA / Velocity 0.1 m / s,
- Without SA / Time 1 μs GPS synchronization time
• DGPS / SBAS position: 2.0 CEP
• Date WGS-84
• Capture rate (95% TTFF first local location)
- Hot start: <1 second, the average outdoor
- Warm start: 35 seconds, the average outdoor
- Cold start: 35 seconds, the average outdoor
• support for AGPS
• Protocol
- NMEA-0183
- SiRF binary
- RTCM SC-104

Performance description
GSM / GPRS indicators
• Quad-band GSM 850/900/1800/1900MHz
• GPRS multi-the slot the Class 10 standard
• GPRS mobile station a Class B standards
• meet the GSM 2/2 + standards
-Class 4 (2W @ GSM850/900MHz)

-Class 1 (1W @ GSM1800/1900MHz)

• AT command and control (GSM 07.07, 07.05 and the SIMCom enhanced AT command set)
• Support STK
• Support for low-power mode
• Supply voltage range: 3.4 ... 4.5 V
• Normal operation temperature: -30 ° C to +80 ° C
• Restricted operation temperature: -40 ° C to -30 ° C and +80 ° C to +85 ° C
• Storage Temperature: -45 ° C to +90 ° C
GPS indicator
• Receiver 20 channels, L1 1575.42 MHz, C / A code 1,023 MHz chip rate
• accurate positioning of the 2.5 m CEP
- Without the SA / Velocity 0.1 m / s,

- Without SA / Time 1 μs GPS synchronization time

• DGPS / SBAS position: 2.0 CEP
• Date WGS-84
• Capture rate (95% TTFF first local location)
- Hot start: <1 second, the average outdoor

- Warm start: 35 seconds, the average outdoor

- Cold start: 35 seconds, the average outdoor

• support for AGPS
• Operating voltage: 3.3 V DC ± 5%
• Low power consumption: 3.3 V, 160mW
• Protocol
-NMEA-0183 (default)

-SiRF binary

-RTCM SC-104

Crystal oscillator (TCXO), frequency stability, temperature ± 0.5ppm
• Memory: 4 Mb flash and 1Mb SRAM
Module features
• implementation of the AT commands through the serial port
• GSM serial port baud rate: 300,1200,2400,4800,9600,19200,38400,57600,115200 bps (default 115200bps)
Available through AT commands to change the baud rate

GSM auto-baud: 4800,9600,19200,38400,57600,115200 bps

• serial output GPS location information
• GPS serial port baud rate: 1200,2400,4800,9600,19200,38400,57600,115200 bps (default 4800bps)
• Supports 6-pin clamshell SIM card holder
• Support for headset, microphone interface
• Support for 4 * 4 matrix keyboard interface
• Module Working voltage: 5V
• Module dimensions: length 82mm, width 70mm
• Module weight:
Distribution list:

Product list:
Module one

GSM test method:

1 the download GSM_Test.pde program to the Arduino control board.

2, the SIM card into the slot on the board of the GPS / GPRS / GSM.

3, the GPS / GPRS / GSM board plugged into the Arduino control board, open the board GSM_PWR switch dial is switched ON.

4, to prepare a USB to TTL serial converter module, bread lines will be converted to the module GND, TX, RX and GPS / GPRS / GSM board GND with, TX, RX-one correspondence connection.

5, the connection good GSM antenna. DC power to the Arduino control board power supply, GPS / GPRS / GSM board of STAT light will shine after the power supply, the GSM part of the already open; NET flashes, if it is 64ms on bright / 3000ms off off, the GSM has to find network.

6 USB to TTL serial port module, plug in the computer's USB port. Open the serial port assistant, select the USB to TTL module port number, baud rate: 115200 data bits: 8 Stop bits: 1 parity bit: none. Select the serial number, and send a new line in front of the box to play √.

7, send characters AT, serial assistant receiver receives the OK, the GSM part is now ready, you can now send text messages, phone calls.